DEPARTMENT OF ENVIRONMENTAL QUALITY, GREAT LAKES, AND ENERGY
AIR QUALITY DIVISION
AIR POLLUTION CONTROL
Filed with the secretary of state on
These rules become effective immediately after filing with the secretary of state unless adopted under section 33, 44, or 45a(9) of the administrative procedures act of 1969, 1969 PA 306, MCL 24.233, 24.244, or 24.245a. Rules adopted under these sections become effective 7 days after filing with the secretary of state.
(By authority conferred on the director of
environment,
Great Lakes, and energy environmental quality by sections 5503
and 5512 of the
natural resources and environmental protection act, 1994 PA 451, MCL
324.5503 and 324.5512, and Executive Reorganization Order Nos. 1995-16,
2009-31, and 2011-1, and 2019-1, MCL 324.99903, 324.99919, and324.99921, and 324.99923)
R 336.1103, R 336.1104, R 336.1113, R 336.1116, R 336.1119, R 336.1120, and
R 336.1122 of the Michigan Administrative Code are amended, as follows:
PART 1. GENERAL PROVISIONS
R 336.1103 Definitions; C.
Rule 103. As used in these rules:
(a) "Calendar day" means a
24-hour time period, which normally is
midnight to midnight, but which may, upon written notification to the
department, cover a different, consecutive 24-hour time period for a specific
process.
(b) "Capacity factor" means the ratio of the average load on a machine or equipment for the period of time considered to the capacity rating of the machine or equipment.
(c) "Carcinogen" means any
either of the following:
(i) Group A -- Any substance for
which there is sufficient evidence from human epidemiological studies to
support a causal association between exposure to the agent and cancer. Belonging to a
category of “carcinogenic to humans,” “likely to be carcinogenic to humans,” or
“suggestive evidence of carcinogenic potential” using the weight of evidence
narrative approach as described in United States Environmental Protection
Agency’s “Guidelines for Carcinogen Risk Assessment” as adopted by reference in
R 336.1902.
(ii) Group B -- Any substance for
which the weight of evidence of human carcinogenicity based on epidemiological
studies is limited evidence or for which the weight of evidence of
carcinogenicity based on animal studies is sufficient evidence. Any chemical that
has been determined to be a carcinogen using another generally accepted
guideline for carcinogen risk assessment based on sound scientific and
defensible evidence.
(iii) Group C -- Any substance for which
there is limited evidence of carcinogenicity in animals in the absence of human
data and which causes a significant increased incidence of benign or malignant
tumors in a single, well-conducted animal bioassay.
(d) "Charging period," with
respect to coke ovens utilizing larry car charging methodology, means the total
time taken between the point at which the coal starts flowing into the oven and
the point at which the leveling door and the charging holes are closed with
their respective lids after the coal from the larry car hoppers is emptied into
the oven being charged through the respective charging holes and the coal has
been leveled in the oven. "Charging period," with
respect to coke ovens utilizing pipeline charging methodology, means the total
time taken from the time at which the coal starts flowing into an oven by
opening the preheated coal inlet valve to the time at which the coal flow ends
when the inlet valve is closed.
(e) "Class II finishes on hardboard paneling
finish" means a finish that meets the specifications of voluntary
product standard PS-59-73, as approved by the American Nnational Sstandards Iinstitute.
(f) "Clean air act" means
chapter 360, 69 stat. 322, 42 USCU.S.C. §§ 7401 to 7431, 7470
to 7479, 7491 to 7492, 7501 to 7509a, 7511 to 7515, 7521 to 7525, 7541 to 7545,
7547 to 7550, 7552 to 7554, 7571 to 7574, 7581 to 7590, 7601 to 7612, 7614 to
7617, 7619 to 7622, 7624 to 7627, 7641 to 7642, 7651 to 7651o, 7661 to 7661f,
and 7671 to 7671q and regulations promulgated under the clean air act.
(g) "Clean charge" means
furnace charge materials, including molten metal; t-bar; sow; ingot; billet;
pig; alloying elements; uncoated/ or unpainted thermally dried metal chips;
metal scrap dried at 343 degrees Celsius, (650 degrees Fahrenheit), or higher; metal
scrap delacquered/ or decoated at 482 degrees Celsius, (900
degrees Fahrenheit), or higher; other oil and lubricant-free unpainted or /uncoated
gates and risers; oil and lubricant-free unpainted/ or uncoated scrap,
shapes, or products, ( pistons for example,
pistons,) that have not
undergone any process, (for
example, machining, coating, painting,) that would cause contamination of
the metal (with oils, lubricants, coatings, or paints;) and on-site
runaround.
(h) "Clear coating" means a
coating which that lacks color and
opacity or is transparent and which uses the undercoat as a reflectant
base or undertone color.
(i) "Clinical testing of
pharmaceuticals" means human or animal health studies that are conducted
consistent with applicable government regulations, guidelines, or directions
for approval of a pharmaceutical product, such as those monitored by the United
States fFood and dDrug aAdministration for
the purpose of determining any of the following with respect to a drug:
(i) Pharmacological action.
(ii) Preferred route of administration.
(iii) Safe dosage range.
(iv) Optimum dosage schedule.
(v) Safety and effectiveness.
(vi) Product label indications.
(j) "Coating category" means a type of surface coating for which there is a separate emission limit specified in these rules.
(k) "Coating line" means an
operation which that is a single series in a coating process
and which is comprised of 1 or more coating applicators and any
associated flash-off areas, drying areas, and ovens wherein 1 or more surface
coatings are applied and subsequently dried or cured.
(l) "Coating of automobiles and light-duty trucks" means the application of prime, primer surfacer, topcoat, and final repair to sheet metal and metallic body components during assembly of a vehicle. Examples of these sheet metal and metallic body components include all of the following:
(i) Bodies.
(ii) Fenders.
(iii) Cargo boxes.
(iv) Doors.
(v) Grill openings.
(m) "Coating of cans" means exterior coating and interior spray coating in 2-piece can lines; interior and exterior coating in sheet coating lines for 3-piece cans; side seam spray coating and interior spray coating in can fabricating lines for 3-piece cans; and sealing compound application and sheet coating in end coating lines.
(n) "Coating of coils" means the coating of any flat metal sheet or strip that comes in rolls or coils.
(o) "Coating of fabric" means the application of any type of coating to flat sheets of a textile substrate, including the application of coatings by saturation or impregnation.
(p) "Coating of flat wood
paneling" means the factory-finished coating of flat products which are
constructed of wood and which are intended for use as interior paneling. This
definition does not apply to the coating of flat wood products intended for use
as exterior siding, tileboard, cabinets, or furniture components.
(qp) "Coating of
large appliances" means the coating of the component metal parts of
residential and commercial washers, dryers, ranges, refrigerators, freezers,
water heaters, dishwashers, trash compactors, air conditioners, and other
associated products. Examples of these component metal parts include all of
the following:
(i) Doors.
(ii) Cases.
(iii) Lids.
(iv) Panels.
(v) Interior support parts.
(rq) "Coating of
metal furniture" means the coating of any furniture made of metal and
includes the coating of any metal part that is or shallmust be assembled with
other metal, wood, fabric, plastic, or glass parts to form a furniture piece.
(sr) "Coating of
paper" means the application of any decorative, functional, or saturation
coating applied across the entire width of any flat sheet or pressure-sensitive
tape, regardless of substrate, or applied across a partial width of any flat
sheet or pressure-sensitive tape, regardless of substrate, if this partial
coverage is not considered to be an operation or series of operations that is
included in the definition of graphic arts line in R 336.1107(e). These
applications and substrates include paper, fabric, or plastic film; related
wet-coating processes on plastic film, including typewriter ribbons,
photographic film, and magnetic tape; and decorative coatings on metal foil,
including gift wrapping and packaging; paperboard; and pressure sensitive tapes
or labels. Excluded from this definition are coatings used in substrate
formation within a papermaking system or coatings applied within all printing
lines including, but not limited to, those that comply with requirements
contained in R 336.1624, R 336.1624a, and R 336.1635.
(ts) "Coating of
plastic parts of automobiles and trucks" means the coating of any plastic
part that is or that can be assembled with
other parts to form an automobile or truck.
(ut) "Coating of
plastic parts of business machines" means the coating of any plastic part
that is or that can be assembled with
other parts to form a business machine.
(vu) "Coating of
vinyl" means any printing, decorative coating, or protective topcoat applied
over vinyl-coated fabric or vinyl rolls or sheets. Coating of vinyl does not
include the application or of plastisols.
(wv) "Coke
battery" means a series of coke ovens arranged side by side with an
integral heating system.
(xw) "Coke
oven" means a chamber in which coal is destructively distilled to yield
coke.
(yx)
"Cokeside," with respect to a coke oven, means that side of the coke
oven through which coke is discharged.
(zy) "Coking
cycle" means the time during which coal undergoes destructive distillation
in a coke oven. The coking cycle commences at the end of the charging period
and ends at the beginning of the pushing operation, but does not include any
decarbonization periods.
(aaz) "Cold
cleaner" means a tank containing organic solvent with a volatile organic
compound content of 5 % or more, by weight, and at a temperature below its
boiling point that is used to spray, brush, flush, or immerse metallic or plastic, or
both metallic and
and/or plastic objects, for the purpose of cleaning or degreasing.
(bbaa) "Commercial
location" means a publicly or privately owned place where persons are
engaged in the exchange or sale of goods or services and multiple housing units
designed for 3 or more families, except for elementary and secondary schools
and facilities owned and operated by the state government. A separate building
or group of buildings used for the exchange or sale of goods or services and
having a single owner and manager constitutes a separate commercial location.
(ccbb) "Completed
organic resin" means organic resin solids, solvents, and additives as
deliverable for sale or use, including a dry organic resin.
(ddcc) "Compliance
plan" means a description of the compliance status of a source with respect
to all applicable requirements for each process or process equipment as
follows:
(i) For applicable requirements with which the source is in compliance, a statement that the source will continue to comply with the requirements.
(ii) For applicable requirements that will become effective during the permit term, a statement that the source will meet the requirements on a timely basis.
(iii) For applicable requirements for which the stationary source is not in compliance at the time of permit issuance, a narrative description of how the stationary source will achieve compliance with the requirements.
(eedd)
"Component" means 1 of the following:
(i) As it pertains to the provisions of
R 336.1622, "component" means any piece of equipment
that has the potential to leak a volatile organic compound and includes all of
the following:
(A) Pump seals.
(B) Compressor seals.
(C) Seal oil degassing vents.
(D) Pipeline valves.
(E) Flanges and other connections.
(F) Pressure-relief devices.
(G) Process drains.
(H) Open ended pipes.
(ii) As it pertains to the provisions
of R 336.1628, "component" means all of the following:
(A) Compressor seals.
(B) Process valves in light liquid or gaseous volatile organic compound service.
(C) Pressure-relief valves in gaseous volatile organic compound service.
(D) Seals of pumps in light liquid service.
(iii) As it pertains to the provisions
of R 336.1629, "component" means all of the following:
(A) Compressor seals.
(B) Process valves.
(C) Pressure-relief valves.
(D) Pump seals.
This definition does not include a valve that is not externally regulated, that is, a valve that has no external controls and thus does not have the potential to leak a volatile organic compound.
(ffee) "Component
in field gas service" means a component that processes, transfers, or
contains field gas.
(ggff) "Component
in gaseous volatile organic compound service" means a component that
processes, transfers, or contains a volatile organic compound in the gaseous
phase under actual conditions.
(hhgg) "Component
in heavy liquid service" means a component that processes, transfers, or
contains heavy liquid.
(iihh) "Component
in light liquid volatile
organic compound
service" means a component that contacts a light liquid containing more
than 10% volatile organic compound by weight.
(jjii) "Component
in liquid volatile organic compound service" means a component that
processes, transfers, or contains a volatile organic compound in the liquid
phase under actual conditions.
(kkjj)
"Condenser" means a device that effects the removal of an air
contaminant from an exhaust stream by a physical change of state from a vapor
to a liquid or solid form.
(llkk) "Control
equipment" means air pollution control equipment.
(mmll)
"Conventional air-atomizing spray equipment" means a device that is
designed to atomize and direct fluid material solely through the use of compressed
air and that is capable of operating at air pressures of more than 10
pounds per square inch.
(nnmm)
"Conveyorized cold cleaner" means any continuous system that
transports metallic
or plastic, or both metallic and plastic objects through a bath containing organic
solvent at a temperature below its boiling point for the purpose of cleaning or
degreasing.
(oonn)
"Conveyorized vapor degreaser" means any continuous system that
transports metallic objects through or over, or through and over, a bath
containing organic solvent that is heated to its boiling point for the purpose
of cleaning or degreasing.
(pp) "Cutback paving
asphalt" means asphalt cement that has been liquefied by blending with a
volatile organic compound and that is used for the purpose of paving or
repairing, or paving and repairing, a road surface.
(qqoo) "Cycle of
operation," with respect to continuous emission monitoring systems, means
the total time a monitoring system requires to sample, analyze, and record an
emission measurement.
R 336.1104 Definitions; D.
Rule 104. As used in these rules:
(a) "Decarbonization period," with respect to coke ovens, means the time for combusting carbon formed at the oven roof and in the standpipe assembly. The decarbonization period commences when a charging hole lid or lids or a standpipe lid or lids are removed or opened near the end of the coking cycle and ends with the initiation of the next charging period.
(b) "Delivery vessel" means any tank truck, tank-equipped trailer, railroad tank car, or any similar vessel equipped with a storage tank used for the transport of a volatile organic compound from sources of supply to any stationary vessel.
(c) "Demolition waste material" means waste building materials that result from demolition operations on houses and commercial and industrial buildings.
(d) "Department" means the director of the department of environment, Great Lakes, and energyenvironmental qualityorhis or herthe director’s designee.
(e) "Difficult-to-monitor component" means a component that can only be monitored by elevating the monitoring personnel more than 6 feet above a support surface.
(f) "Dispensing facility" means a location where gasoline is transferred to a motor vehicle tank from a stationary vessel."Dry organic resin" means the organic resin solids from which all liquids have been removed, as deliverable for sale or use.
(g) "Dry organic resin" means the organic resin solids from which all liquids have been removed, as deliverable for sale or use."Dispensing facility" means a location where gasoline is transferred to a motor vehicle tank from a stationary vessel.
R 336.1113 Definitions; M.
Rule 113. As used in these rules:
(a) "Malfunction" means any sudden, infrequent and not reasonably preventable failure of a source, process, process equipment, or air pollution control equipment to operate in a normal or usual manner. Failures that are caused in part by poor maintenance or careless operation are not malfunctions.
(b) "Market testing andor market
development" means the limited or general distribution of a product to the
consumer to gather information concerning the demand for the product.
(c) "Material handling equipment," as referenced in table 31 of R 336.1331, means a device, contrivance, or equipment used to bag, blend, convey, crush, grind, load, mill, mix, shed, store, transfer, or unload a physical substance.
(d) "Material recovery equipment" means any equipment utilized in the transport and recovery of styrene monomer and other impurities from other products and by-products in the manufacture of polystyrene resin by continuous process, including the styrene devolatilizer unit and styrene recovery unit.
(e) “Minus water” means subtraction of water and compounds that are used as organic solvents and excluded from the definition of volatile organic compound.
(f) "Modify" means making a
physical change in, or change in the method of operation of, existing process
or process equipment which that increases the amount of any air
contaminant emitted into the outer air which that is not already
allowed to be emitted under the conditions of a permit or order or which
results in the emission of any toxic air contaminant into the outer air not
previously emitted. An increase in the hours of operation or an increase in
the production rate up to the maximum capacity of the process or process
equipment is shall not be
considered to be a change in the method of operation unless the process or
process equipment is subject to enforceable permit conditions or enforceable
orders which that limit the
production rate or the hours of operation, or both, to a level below the
proposed increase.
(fg) "Motor
vehicle" means any self-propelled vehicle registered for, or requiring
registration for, use on the highway.
(h) “Motor vehicle material” means coatings applied to motor vehicles or motor vehicle components at facilities that are not automobile or light-duty truck assembly coating facilities.
R 336.1116 Definitions; P.
Rule 116. As used in these rules:
(a) "Packaging rotogravure printing" means rotogravure printing upon a substrate that, in subsequent operations, is formed into a packaging product or label, or both.
(b) "Paint manufacturing" means the grinding or mixing of a combination of pigments, resins, and liquids to produce a surface coating as listed in standard industrial classification code 2851.
(c) "Particulate matter" means any air contaminant existing as a finely divided liquid or solid, other than uncombined water, as measured by a reference test specified in R 336.2004(5) or by an equivalent or alternative method.
(d) "Perchloroethylene dry cleaning equipment" means equipment utilized in the cleaning of fabrics for which perchloroethylene (tetrachloroethylene) is the predominant cleaning medium.
(e) "Performance test" means
the taking of a source sample at a stationary source, by employing
department-approved methods, to determine either of the following:
(i) Compliance with the department's rules, orders, or emission limitations.
(ii) Compliance with the conditions of a permit to install or renewable operating permit.
(f) "Permit to install" means a permit issued by the department authorizing the construction, installation, relocation, or alteration of any process, fuel-burning, refuse-burning, or control equipment in accordance with approved plans and specifications.
(g) "Permit to operate" means
a permit issued by the department authorizing the use of any process,
fuel-burning, refuse-burning, or control equipment for the period indicated
after it has been demonstrated that it can be operated in compliance with these
rules. The requirement to obtain a permit to operate was removed from these
rules effective July 26, 1995. Permits to operate issued before that date
remain in effect effective and legally enforceable unless they are
voided pursuant to R 336.1201(6).
(h) "Person" means any of the following:
(i) An individual person.
(ii) Trustee.
(iii) Court-appointed representative.
(iv) Syndicate.
(v) Association.
(vi) Partnership.
(vii) Firm.
(viii) Club.
(ix) Company.
(x) Corporation.
(xi) Business trust.
(xii) Institution.
(xiii) Agency.
(xiv) Government corporation.
(xv) Municipal corporation.
(xvi) City.
(xvii) County.
(xviii) Municipality.
(xix) District.
(xx) Other political subdivision, department, bureau, agency, or instrumentality of federal, state, or local government.
(xxi) Other entity recognized by law as the subject of rights and duties.
(i) "Petroleum" means the crude oil removed from the earth and the oils derived from tar sands, shale, and coal gasification or liquefaction.
(j) "Petroleum refinery" means any facility engaged in producing gasoline, kerosene, distillate fuel oils, residual fuel oils, lubricants, or other products through distillation of petroleum or through redistillation, cracking, or the reforming of unfinished petroleum derivatives.
(k) "PM-10" means particulate
matter that has an aerodynamic diameter less than or equal to a nominal 10
micrometers, as measured by a reference test specified in 40 C.F.R. part
51, appendix M, adopted by reference in R 336.1902. PM-10 emissions shall
must include gaseous
emissions from a source or activity which that condense to form
particulate matter at ambient temperatures. Such The condensable
particulate matter shallmust be accounted for in applicability
determinations and in establishing emissions limitations for PM-10.
(l) “PM 2.5” means particulate matter
that has an aerodynamic diameter less than or equal to a nominal 2.5
micrometers, as measured by a reference test specified in 40 C.F.R. part 51,
appendix M, adopted by reference in R 336.1902. PM 2.5 emissions shallmust include gaseous
emissions from a source or activity that condense to form particulate matter at
ambient temperatures. Such The condensable particulate matter shallmust be accounted for
in applicability determinations and in establishing emissions limitations for
PM 2.5.
(m) "Potential emissions"
means those emissions expected to occur without control equipment, unless this
control equipment is, aside from air pollution control requirements, vital to
production of the normal product of the source or to its normal operation.
Annual potential emissions shallmust be based on the maximum
annual-rated capacity of the source, unless the source is subject to
enforceable permit conditions or enforceable orders that limit the operating
rate or the hours of operation, or both. Enforceable agreements or permit
conditions on the type or amount of materials combusted or processed shallmust be used in
determining the potential emission rate of a source.
(n) "Potential to emit" means
the maximum capacity of a stationary source to emit an air contaminant under
its physical and operational design. Any physical or operational limit on the
capacity of the stationary source to emit an air contaminant, including air
pollution control equipment and restrictions on the hours of operation or the
type or amount of material combusted, stored, or processed, shallmust be treated as
part of its design only if the limit, or the effect it would have on emissions,
is legally enforceable. Secondary emissions shall do not count in
determining the "potential to emit" of a stationary
source. For hazardous air pollutants that have been listed pursuant to Section
112(b) of the clean air act, quantifiable fugitive emissions shallmust be included in
determining the potential to emit of any stationary source. For all other air
contaminants, quantifiable fugitive emissions shallmust be included in
determining the "potential to emit" of a stationary
source only if the stationary source belongs to 1 of the following categories:
(i) Coal cleaning plants that have thermal dryers.
(ii) Kraft pulp mills.
(iii) Portland cement plants.
(iv) Primary zinc smelters.
(v) Iron and steel mills.
(vi) Primary aluminum ore reduction plants.
(vii) Primary copper smelters.
(viii) Municipal incinerators capable of charging more than 50 tons of refuse per day.
(ix) Hydrofluoric, sulfuric, or nitric acid plants.
(x) Petroleum refineries.
(xi) Lime plants.
(xii) Phosphate rock processing plants.
(xiii) Coke oven batteries.
(xiv) Sulfur recovery plants.
(xv) Carbon black plants that have a furnace process.
(xvi) Primary lead smelters.
(xvii) Fuel conversion plants.
(xviii) Sintering plants.
(xix) Secondary metal production plants.
(xx) Chemical process plants. The term chemical process plant does not include ethanol production facilities that produce ethanol by natural fermentation included in North American industrial classification system codes 325193 or 312140.
(xxi) Fossil fuel boilers, (or combination
thereof,) totaling more
than 250,000,000 Btu per hour heat input.
(xxii) Petroleum storage and transfer units that have a total storage capacity of more than 300,000 barrels or petroleum storage vessels that have a capacity of more than 40,000 gallons.
(xxiii) Taconite ore processing plants.
(xxiv) Glass-fiber processing plants.
(xxv) Charcoal production plants.
(xxvi) Fossil fuel-fired steam electric plants of more than 250,000,000 Btu per hour heat input.
(xxvii) Asphalt concrete plants.
(xxviii) Secondary lead smelters and refineries.
(xxix) Sewage treatment plants.
(xxx) Phosphate fertilizer plants.
(xxxi) Ferroalloy production plants.
(xxxii) Grain elevators.
(xxxiii) Stationary gas turbines.
(xxxiv) Stationary sources that are
subject to the Federal
National Emission Standards for Hazardous Air Pollutants federal national
emission standards for hazardous air pollutants for the following
materials:
(A) Asbestos.
(B) Beryllium.
(C) Mercury.
(D) Vinyl chloride.
(o) "PPM" means parts per million, by volume.
(p) "Printed interior panel" means a panel that has its grain or natural surface obscured by fillers and basecoats and upon which a simulated grain or decorative pattern is printed.
(q) "Process" means an action,
operation, or a series of actions or operations at a source that emits or has
the potential to emit an air contaminant. Examples of a "process"
include any of the following:
(i) A physical change of a material.
(ii) A chemical change of a material.
(iii) The combustion of fuel, refuse, or waste material.
(iv) The storage of a material.
(v) The handling of a material.
(r) "Process equipment" means all equipment, devices, and auxiliary components, including air pollution control equipment, stacks, and other emission points, used in a process.
(s) "Process unit turnaround" means the scheduled shutdown of a refinery process unit for the purpose of inspection or maintenance of the unit.
(t) "Production equipment exhaust system" means a device for collecting and removing, from the immediate area, fugitive air contaminants from any process equipment.
(u) "Psia" means pounds per square inch absolute.
(v) "Publication rotogravure printing" means rotogravure printing upon a substrate that is subsequently formed into any of the following:
(i) Book.
(ii) Magazine.
(iii) Catalogue.
(iv) Brochure.
(v) Directory.
(vi) Newspaper.
(vii) Supplement.
(viii) Other type of printed material.
(w) "Pushing operation," with respect to coke ovens, means the movement of the coke from a coke oven into the coke-receiving car.
(x) "Pushside," with respect to a coke oven, means that side of the coke oven that is adjacent to the pushing machine.
R 336.1119 Definitions; S.
Rule 119. As used in these rules:
(a) "Schedule of compliance" means, for purposes of R 336.1201 to R 336.1218, all of the following:
(i) For a source not in compliance with
all applicable requirements at the time of issuance of a renewable operating
permit, a schedule of remedial measures, including an enforceable sequence of
actions or operations that specifies milestones, leading to compliance with an
applicable requirement, and a schedule for submission of certified progress
reports, at least not less than every 6 months. The schedule shallmust resemble, and be at
least as stringent as, a schedule contained in a judicial consent decree or
administrative order to which the source is subject. A schedule shallmust be supplemental
to, and shall not sanction noncompliance with, the applicable requirement on which it is based.
(ii) For a source in compliance with all applicable requirements at the time of issuance of a renewable operating permit, a statement that the source will continue to comply with the requirements.
(iii) With respect
to any applicable requirement that has a future effective compliance date that
is after the date of issuance and before the date of expiration of the
renewable operating permit, the schedule of compliance shallmust contain a statement that the source will meet the
requirement on a timely basis, unless the underlying applicable requirement
requires a more detailed schedule.
(b) "Secondary emissions"
means emissions which that occur as a result of the
construction or operation of a stationary source, but which do not come
from the stationary source itself. Secondary emissions include only emissions
that are specific, well-defined, quantifiable, and impact the same general area
as the stationary source which causes the secondary emissions. Secondary
emissions also include emissions from any off-site support facility which
that would not
otherwise be constructed or increase its emissions except as a result of the
construction or operation of the stationary source. Examples of secondary
emissions include the following:
(i) Emissions from ships or trains coming to or going from a stationary source.
(ii) Emissions from any off-site support facility that would not otherwise be constructed or increase its emissions except as a result of the construction or operation of the stationary source.
(c) "Secondary
risk screening level" means the concentration of a possible, probable, or
known human carcinogen in ambient air which has been that is calculated, for
regulatory purposes, according to the risk assessment procedures in R 336.1229(1), to produce an estimated upper-bound
lifetime cancer risk of 1 in 100,000.
(d) "Shutdown" means the cessation of operation of a source for any purpose.
(e) "Significant"
means a rate of emissions for the following air contaminants which that would equal or
exceed any of the following:
(i) Carbon monoxide - 100 tons per year.
(ii) Oxides of nitrogen - 40 tons per year.
(iii) Sulfur dioxide - 40 tons per year.
(iv) Particulate matter - 25 tons per year.
(v) PM-10 - 15 tons per year.
(vi) PM 2.5 - 10 tons per year, 40 tons per year of sulfur dioxide, or 40 tons per year of oxides of nitrogen.
(vii) Volatile organic compounds - 40 tons per year.
(viii) Lead - 0.6 tons per year.
(ix) Fluorides - 3 tons per year.
(x) Sulfuric acid mist - 7 tons per year.
(xi) Hydrogen sulfide - 10 tons per year.
(xii) Total reduced sulfur, including hydrogen sulfide - 10 tons per year.
(xiii) Reduced sulfur compounds, including hydrogen sulfide - 10 tons per year.
(xiv) Municipal waste combustor organics, measured as total tetra- through octa-chlorinated dibenzo-p-dioxins and dibenzofurans - 3.2x10-6 megagrams per year or 3.2x10‑6 tons per year.
(xv) Municipal waste combustor metals, measured as particulate matter – 14 megagrams per year or 15 tons per year.
(xvi) Municipal waste combustor acid gases, measured as sulfur dioxide and hydrogen chloride - 36 megagrams per year or 40 tons per year.
(xvii) Municipal solid waste landfill emissions, measured as nonmethane organic compounds - 45 megagrams per year or 50 tons per year.
(f) "Smoke" means small gas and airborne particles consisting essentially of carbonaceous material in sufficient numbers to be observable.
(g) "Sour condensate" means a condensate that emits sour gas at atmospheric pressure.
(h) "Sour crude" means a crude oil that emits sour gas at atmospheric pressure.
(i) "Sour gas" means any gas containing more than 1 grain of hydrogen sulfide or more than 10 grains of total sulfur per 100 standard cubic feet.
(j) "Source sample" means any
raw material, fuel, product, by-product, waste material, exhaust gas, air
contaminant, flora, soil, or other such material existing as a gas,
liquid, or solid, which is captured, retained, or collected from a stationary
source.
(k) Reserved."Specific
plate collection area" means the ratio of the total collection area to the
total gas volume flow rate in square feet per 1,000 actual cubic feet per
minute.
(l) "Stack" or "chimney" means a flue, conduit, or duct arranged to conduct a gas stream to the outer air.
(m) "Standard conditions" means a gas temperature of 70 degrees Fahrenheit and a gas pressure of 29.92 inches of mercury absolute.
(n) "Standpipe assembly," with respect to coke ovens, means the riser, standpipe lid, and the gooseneck.
(o) "Standpipe assembly emission
point," with respect to a coke oven battery equipped with a single
collector main or a double collector main, means the flexible connection
between the battery top and the base of the riser, the seating surface of the
standpipe lid, and the second flexible connection wherever located, or another
agreed upon connection that is located between the collector main and the
gooseneck. With respect to a battery equipped with a charging main and a
gas-offtake main in tandem, "standpipe assembly emission point"
means the upper flange, the lower flange, the top lid, the bottom lid, the
upper sand seal, the middle sand seal, and the lower base sand seal. With
respect to a battery equipped with a jumper pipe ministandpipe, "standpipe
assembly emission point" means the flexible connection between the
battery top and the base of the riser, the seating surface of the standpipe
lid, the flexible connection between the collector main and the gooseneck, the
ministandpipe lid, and the flexible connection between the battery top and the
jumper pipe ministandpipe.
(p) "Start-up" means the setting in operation of a process or process equipment for any purpose.
(q) “State-only enforceable” means that
the limitation or condition is derived solely from the act and the air
pollution control rules and is not federally enforceable. State-only
enforceable requirements include R 336.1224, R 336.1225, R 336.1901, any permit
requirement established solely pursuant to R 366.1201(1)(b), or any other
another regulation that
is enforceable solely under the act and is not federally enforceable.
(r) "Stationary source" means
all buildings, structures, facilities, or installations that emit or have the
potential to emit 1 or more air contaminants, which are located at 1 or
more contiguous or adjacent properties, which are under the control of
the same person, and which have the same 2-digit major group code
associated with their primary activity. In addition, a stationary source
includes any other buildings, structures, facilities, or installations which
that emit or have the
potential to emit 1 or more air contaminants, which are located at 1 or
more contiguous or adjacent properties, which are under the control of
the same person, and which have a different 2-digit major group code,
but which support the primary activity. Buildings, structures,
facilities, or installations, are considered to support the primary
activity if 50% or more of their output is dedicated to the primary activity.
Major group codes and primary activities are described in the standard
industrial classification manual. Notwithstanding the provisions of this
subdivision, research and development activities, as described in R 336.1118,
may be treated as a separate stationary source, unless the research and
development activities support the primary activity of the stationary source.
(s) "Stationary vessel" means
any tank, reservoir, or container used for the storage of any volatile organic
compound which that is not used to
transport such volatile organic compounds and in which
no manufacturing process or part thereof takes place.
(t) "Stencil coat" means a coating that is applied over a stencil to a plastic part at a thickness of 1 mil or less of coating solids. Stencil coats are most frequently letters, numbers, or decorative designs.
(u) "Styrene devolatilizer unit" means equipment performing the function of separating unreacted styrene monomer and other volatile components from polystyrene in a vacuum devolatilizer.
(v) "Styrene recovery unit" means equipment performing the function of separating styrene monomer from other less volatile components of the styrene devolatilizer unit's output. The separated styrene monomer may be reused as raw material in the manufacturing of polystyrene resin.
(w) "Submerged fill pipe" means any fill pipe that has its discharge opening entirely submerged when the liquid level is 6 inches above the bottom of the vessel or, when applied to a vessel that is loaded from the side, means either of the following:
(i) Any fill pipe that has its discharge opening entirely submerged when the liquid level is 18 inches above the bottom of the vessel.
(ii) Any fill pipe that has its
discharge opening entirely submerged when the liquid level is twice the
diameter of the fill pipe above the bottom of the vessel, but in no case shall
the top of such the submerged fill pipe must not be more than 36
inches above the bottom of the vessel.
(x) "Sufficient evidence," a term of art, means either of the following:
(i) In human epidemiological studies, that the data indicates that there is a causal relationship between the agent and human cancer.
(ii) In animal studies, the data suggests that there is an increased incidence of malignant tumors or combined malignant and benign tumors in any of the following:
(A) Multiple species or strains.
(B) Multiple experiments.
(C) To an unusual degree in a single experiment with regard to high incidence, unusual site or type of tumor, or early age at onset.
(y) "Sulfuric acid plant" means any facility producing sulfuric acid by the contact process by burning elemental sulfur, alkylation acid, hydrogen sulfide, or acid sludge, but does not include facilities where conversion to sulfuric acid is utilized primarily as a means of preventing emissions to the atmosphere of sulfur dioxide or other sulfur compounds.
(z) "Surface coating" means any paint, lacquer, varnish, ink, adhesive, or other coating material applied on a surface.
(aa) "Sweet condensate" means any condensate that is not a sour condensate.
(bb) "Sweet crude" means any crude oil that is not a sour crude.
(cc) "Sweetening facility"
means a facility or process that removes hydrogen sulfide or sulfur-containing
compounds, or both, from a sour gas, sour crude oil, or sour condensate stream
and converts it to sweet gas, sweet crude, or sweet condensate. The term "sweetening
facility" does not include a facility or process that operates in
an enclosed system and does not emit hydrogen sulfide to the outer air.
(dd) "Sweet gas" means any gas that is not a sour gas.
(ee) “Synthetic natural gas” means any
manufactured fuel gas of approximately the same composition and BTU valueheating
value as that obtained naturally from oil fieldsgeological
formations beneath the Earth’s surface.
(ff) "Synthetic organic chemical and polymer manufacturing plant" means a stationary source where the production, as intermediates or final products, of 1 or more of the following chemicals takes place:
(i) Methyl tert-butyl ether.
(ii) Polyethylene.
(iii) Polypropylene.
(iv) Polystyrene.
(v) Synthetic organic chemicals listed
in "Standards of Performance for Equipment Leaks of VOC in the Synthetic
Organic Chemicals Manufacturing Industry," 40 C.F.R.
part 60, subpart VV, adopted by reference in R 336.1902.
(gg) "Synthetic organic chemical and polymer manufacturing process unit" means all process equipment assembled to manufacture, as intermediates or final products, 1 or more of the chemicals listed in the definition of synthetic organic chemical and polymer manufacturing plant. A synthetic organic chemical and polymer manufacturing process unit can operate independently if supplied with sufficient feed or raw materials and sufficient storage facilities for the product.
R 336.1120 Definitions; T.
Rule 120. As used in these rules:
(a) "Temporary source" means a stationary source, process, or process equipment that commences operation and is located at a geographic site for not more than 12 consecutive months.
(b) "Texture coat" means a coating that is applied to a plastic part which, in its finished form, consists of discrete raised spots of the coating.
(c) "Thin particleboard" means
a manufactured board that is 1/4 of an inch or less in thickness and which
is made of individual wood particles that have been coated with a binder and
formed into flat sheets by pressure.
(d) "Thinning tank," as it pertains to R 336.1631, means any vessel that receives resin from a reactor and to which solvents or other materials are added to thin the resin.
(e) "Tileboard" means paneling that has a colored, waterproof surface coating.
(f) "Toxic
air contaminant" or "TAC" means any air contaminant for
which there is no national ambient air quality standard and which is or
may become harmful to public health or the environment when present in the
outdoor atmosphere in sufficient quantities and duration. For the purpose of this
definition, all of the following substances shall not be are
not considered to be toxic air contaminants:
(i) Acetylene.
(ii) Aluminum metal dust.
(iii) Aluminum oxide (nonfibrous
forms).
(iv) Ammonium sulfate.
(vii) Animal or plant
materials, including extracts and concentrates thereof, used as ingredients in
food products or dietary supplements in accordance with applicable regulations
of the United States Food and dDrug Administration.
(viii) Argon.
(ivii) Calcium carbonate.
(viii) Calcium hydroxide.
(vix) Calcium oxide.
(xvii) Calcium
silicate.
(xviii) Calcium sulfate.
(ixii) Carbon dioxide.
(xiii) Carbon monoxide.
(xiv) Cellulose.
(xv) Coal dust.
(xvii) Crystalline
silica emissions from any of the following processes:
(A) Extraction and processing of all metallic or non-metallic minerals.
(B) Sand production, processing, and drying.
(C) Asphalt production.
(D) Concrete production.
(E) Glass and fiberglass manufacturing.
(F) Foundries.
(G) Foundry residual recovery activities.
(H) Any other process if the
crystalline silica emissions are less than 10% of the total PM-10 emissions.
(xiii)Dipropylene glycol
(xivii) Emery (corundite).
(xviii) Ethane.
(xixvi) Graphite
(synthetic).
(xxvii) Grain dust.
(xxvii) Helium.
(xixii) Hydrogen.
(xxiii) Iron oxide.
(xxiv) Lead.
(xxvii) Liquefied
petroleum gas (l.p.g.).
(xxviii) Methane.
(xxivii) Neon.
(xxviii) Nitrogen.
(xxviii) Nitrogen oxides.
(xxx) Nuisance particulates.
(xxxvii) Oxygen.
(xxxviii) Ozone.
(xxixiii) Perlite.
(xxxiv) Portland cement.
(xxxvi) Propane.
(xxxvii) Propylene glycol
(xxxiii) Silicon.
(xxxivii) Starch.
(xxxviii) Sucrose.
(xxxixvi) Sulfur dioxide.
(xlxxvii) Vegetable oil
mist.
(xlxxviii) Water vapor.
(xlixxix) Zinc metal dust.
(g) "Toxicological
interaction" means the simultaneous exposure to 2 or more hazardous
substances that
which togetherwill produce a
toxicological response that is greater or less than what their individual
responses would
be.
(h) "Transfer efficiency" means the percentage of coating solids material that leaves the coating applicator and remains on the surface of the product.
(i) "True vapor pressure"
means the equilibrium partial pressure exerted by a liquid or the sum of
partial pressures exerted by a mixture of liquids. For refined petroleum stock, ( such as gasolines and
naphthas,) and crude oil,
the "true vapor pressure" may be determined in
accordance with methods described in American petroleum institute MPMS C19 S2,
"Manual of Petroleum Measurement Standards, Chapter 19, Evaporative Loss
Measurements, Section 2, Evaporative Loss From from Floating-Rroof Tanks,"
adopted by reference in R 336.1902.
R 336.1122 Definitions; V.
Rule 122. As used in these rules:
(a) "Vacuum-metalizing
coatings" means topcoats and basecoats that are used in the
vacuum-metalizing process.
(b) "Vacuum-producing system" means any device that creates a pressure below atmospheric, such as a pump or steam ejector with condenser, including hot wells and accumulators.
(c) "Vapor collection system,"
as it pertains to R 336.1627, means all piping, seals, hoses, connections,
pressure-vacuum vents, and any other equipment between and including the
delivery vessel and a stationary vessel, vapor processing unit, or vapor
holder.
(d) [Reserved]
(e) "Visible emission" means any emissions that are visually detectable without the aid of instruments.
(f)
"Volatile organic compound" means any compound of carbon or mixture
of compounds of carbon that participates in photochemical reactions, excluding
the following materials, all of which have been determined by the United States
Eenvironmental Pprotection Aagency to have
negligible photochemical reactivity:
(i) Carbon monoxide (CAS No. 630-08-0).
(ii) Carbon dioxide (CAS No. 124-38-9).
(iii) Carbonic acid (CAS No. 463-79-6).
(iv) Metallic carbides or carbonates (CAS No. not applicable).
(v) Boron carbide (CAS No. 12069-32-8 or 60063-34-5).
(vi) Silicon carbide (CAS No. 409-21-2 or 12327-32-1).
(vii) Ammonium carbonate (CAS No. 10361-29-2 or 506-87-6).
(viii) Ammonium bicarbonate (CAS No. 1066-33-7).
(ix) Methane (CAS No. 74-82-8).
(x) Ethane (CAS No. 74-84-0).
(xi) The methyl chloroform (CAS No. 71-55-6) portion of commercial grades of methyl chloroform, if all of the following provisions are complied with:
(A) The commercial grade of methyl chloroform is used only in a surface coating or coating line that is subject to the requirements part 6 or 7 of these rules.
(B) The commercial grade of methyl chloroform contains no stabilizers other than those listed in table 11.
(C) Compliance with the applicable limits specified in parts 6 or 7 of these rules is otherwise not technically or economically reasonable.
(D) All measures to reduce the levels
of all organic solvents, including the commercial grade of methyl chloroform,
from the surface coating or coating line to the lowest reasonable level, will be are implemented.
(E) The emissions of the commercial grade of methyl chloroform do not result in a maximum ambient air concentration exceeding any of the allowable ambient air concentrations listed in table 11.
(F) The use of the commercial grade of methyl chloroform is specifically identified and allowed by a permit to install, permit to operate, or order of the department.
(G) Table 11 reads as follows:
TABLEable 11.
Commercial Grade of Methyl Chloroform -- Allowable Ambient Air Concentrations
Compound |
Ppm1 |
Time2 |
||
Methyl chloroform |
3.5 |
1 hour |
||
Tertiary butyl alcohol3 |
1.0 |
1 hour |
||
Secondary butyl alcohol3 |
1.0 |
1 hour |
||
Methylal3 |
10.0 |
1 hour |
||
1,2-butylene oxide3 |
0.028 and 0.00041 |
1 hour
annual |
||
1 Parts per million, by volume 2 Averaging time period 3 This compound is a stabilizer |
|
|
||
(xii) The methyl chloroform (CAS No. 71-55-6) portion of
commercial grades of methyl chloroform that contain any other another stabilizer not
listed in table 11 of this rule, if all of the following provisions are
complied with:
(A) The commercial grade of methyl chloroform is used only in a surface coating or coating line that is subject to the requirements of parts 6 or 7 of these rules.
(B) Compliance with the applicable limits specified in parts 6 or 7 of these rules is otherwise not technically or economically reasonable.
(C) All measures to reduce the levels
of all organic solvents, including the commercial grade of methyl chloroform,
from the surface coating or coating line to the lowest reasonable level will
be are implemented.
(D) The emissions of any compound in the commercial grade of methyl chloroform that is listed in table 11 of this rule do not result in a maximum ambient air concentration exceeding any of the allowable ambient air concentrations listed in table 11.
(E) The emission of all compounds in the commercial grade of methyl chloroform that are not listed in table 11 is demonstrated to comply with R 336.1901.
(F) The use of the commercial grade of methyl chloroform is specifically identified and allowed by a permit to install, permit to operate, or order of the department.
(xiii) Acetone (CAS No. 67-64-1).
(xiv) Cyclic, branched, or linear completely methylated siloxanes (CAS Nos. include 107-45-0, 107-51-7, 141-62-8, 141-63-9, 107-63-9, 63148-62-9, 541-05-9, 556-67-2, 541-02-6, 540-97-6, 69430-24-6, 17928-28-8, 3555-47-3).
(xv) Parachlorobenzotrifluoride (CAS No. 98-56-6).
(xvi) Perchloroethylene (CAS No. 127-18-4).
(xvii) Trichlorofluoromethane (CFC-11) (CAS No. 75-69-4).
(xviii) Dichlorodifluoromethane (CFC-12) (CAS No. 75-71-8).
(xix) 1,1,2-trichloro-1,2,2-trifluoroethane (CFC-113) (CAS No. 76-13-1).
(xx) 1,2-dichloro 1,1,2,2-tetrafluoroethane (CFC-114) (CAS No. 76-14-2).
(xxi) Chloropentafluoroethane (CFC-115) (CAS No. 76-15-3).
(xxii) 1,1-dichloro 1-fluoroethane (HCFC-141b) (CAS No. 1717-00-6).
(xxiii) 1,chloro 1,1-difluoroethane (HCFC-142b) (CAS No. 75-68-3).
(xxiv) Chlorodifluoromethane (HCFC-22) (CAS No. 75-45-6).
(xxv) 1,1,1-trifluoro 2,2-dichloroethane (HCFC-123) (CAS No. 306-83-2).
(xxvi) 2-chloro-1,1,1,2-tetrafluoroethane (HCFC-124) (CAS No. 2837-89-0).
(xxvii) Trifluoromethane (HFC-23) (CAS No. 75-46-7).
(xxviii) Pentafluoroethane (HFC-125) (CAS No. 354-33-6).
(xxix) 1,1,2,2-tetrafluoroethane (HFC-134) (CAS No. 359-35-3).
(xxx) 1,1,1,2-tetrafluoroethane (HFC-134a) (CAS No. 811-97-2).
(xxxi) 1,1,1-trifluoroethane (HFC-143a) (CAS No. 420-46-2).
(xxxii) 1,1-difluoroethane (HFC-152a) (CAS No. 75-37-6).
(xxxiii) 3,3-dichloro-1, 1,1,2,2-pentafluoropropane (HCFC-225ca) (CAS No. 422‑56-0).
(xxxiv) 1,3-dichloro-1,1,2,2,3-pentafluoropropane (HCFC-225cb) (CAS No. 507‑55‑1).
(xxxv) 1,1,1,2,3,4,4,5,5,5-decafluoropentane (HFC 43-10mee) (CAS No. 138495‑42‑8).
(xxxvi) Difluoromethane (HFC-32) (CAS No. 75-10-5).
(xxxvii) Ethyl fluoride (HFC-161) (CAS No. 353-36-6).
(xxxviii) 1,1,1,3,3,3-hexafluoropropane (HFC-236fa) (CAS No. 690-39-1).
(xxxix) 1,1,2,2,3-pentafluoropropane (HFC-245ca) (CAS No. 679-86-7).
(xl) 1,1,2,3,3- pentafluoropropane ( HFC-245ea) (CAS No. 24270-66-4).
(xli) 1,1,1,2,3- pentafluoropropane (HFC-245eb) (CAS No. 431-31-2).
(xlii) 1,1,1,3,3- pentafluoropropane (HFC-245fa) (CAS No. 460-73-1).
(xliii) 1,1,1,2,3,3-hexafluoropropane (HFC-236ea) (CAS No. 431-63-0).
(xliv) 1,1,1,3,3-pentafluorobutane (HFC365mfc) (CAS No. 406-58-6).
(xlv) Chlorofluoromethane (HCFC-31) (CAS No. 593-70-4).
(xlvi) 1,2-dichloro-1,1,2-trifluoroethane (HCFC-123a) (CAS No. 354-23-4).
(xlvii) 1-chlor-1-fluoroethane (HCFC-151a) (CAS No. 1615-75-4).
(xlviii) 1,1,1,2,2,3,3,4,4-nonafluoro-4-methoxy-butane (C4F9OCH3 or HFE-7100) (CAS No. 163702-07-6).
(xlix) 2-(difluoromethoxymethyl)-1,1,1,2,3,3,3-heptafluoropropane (CAS No. 163702-08-7).
(l) 1-ethoxy-1,1,2,2,3,3,4,4,4-nonafluorobutane (C4F9OC2H5 or HFE-7200) (CAS No. 163702‑05‑4).
(li) 2-(ethoxydifluoromethyl)-1,1,1,2,3,3,3-heptafluoropropane (CAS No. 163702‑06-5).
(lii) Methyl acetate (CAS No. 79-20-9).
(liii) Perfluorocarbon compounds that fall into the following classes:
(A) Cyclic, branched, or linear, completely fluorinated alkanes.
(B) Cyclic, branched, or linear, completely fluorinated ethers with no unsaturations.
(C) Cyclic, branched, or linear, completely fluorinated tertiary amines with no unsaturations.
(D) Sulfur-containing perfluorocarbons with no unsaturations and with sulfur bonds only to carbon and fluorine.
(liv) Methylene chloride (CAS No. 75-09-2).
(lv) 1,1,1,2,2,3,3-heptafluoro-3-methoxy-propane (n-C3F7OCH3, HFE-7000) (CAS No. 375‑03‑1).
(lvi) 3-ethoxy-1,1,1,2,3,4,4,5,5,6,6,6-dodecafluoro-2-(trifluoromethyl) hexane (HFE 7500) (CAS No. 297730-93-9).
(lvii) 1,1,1,2,3,3,3-heptafluoropropane (HFC 227ea) (CAS No. 431-89-0).
(lviii) Methyl formate (HCOOCH3) (CAS No. 107-31-3).
(lix) T-butyl acetate (CAS No. 540-88-5).
(lx) 1,1,1,2,2,3,4,5,5,5-decafluoro-3-methoxy-4-trifluoromethyl-pentane (HFE-7300) (CAS No. 132182-92-4).
(lxi) Dimethyl carbonate (CAS No. 616-38-6).
(lxii) Propylene carbonate (CAS No. 108-32-7).
(lxiii) 2,3,3,3-tetrafluoropropene (HFO–1234yf) (CAS No. 754-12-1).
(lxiv) Trans-1,3,3,3-tetrafluoropropene (HFO–1234ze) (CAS No. 29118-24-9).
(lxv) HCF2OCF2H (HFE-134) (CAS No. 1691-17-4).
(lxvi) HCF2OCF2OCF2H (HFE-236cal2) (CAS No. 78522-47-1).
(lxvii) HCF2OCF2CF2OCF2H (HFE-338pcc13) (CAS No. 188690-78-0).
(lxviii) HCF2OCF2OCF2CF2OCF2H (H-Galden 1040X or H-Galden ZT 130 (or 150 or 180)) (CAS No. 188690-77-9).
(lxix) Trans 1-chloro-3,3,3-trifluoroprop-1-ene (SolsticeTM 1233zd(E)) (CAS No. 102687‑65‑0).
(lxx) 2-amino-2-methyl-1-propanol (AMP) (CAS No. 124-68-5).
(lxxi) 1,1,2,2-Tetrafluoro-1,-(2,2,2-trifluoroethoxy) ethane (HFE-347pcf2) (CAS No. 406-78-0).
(lxxii) cis-1,1,1,4,4,4-hexafluorobut-2-ene (HFO-1336mzz-Z) (CAS No. 692‑49‑9).
(lxxiii) trans-1,1,1,4,4,4-hexafluorobut-2-ene (HFO-1336mzz(E)) (CAS No. 66711-86-2).
The methods described in R 336.2004 and R 336.2040
shallmust be used for
measuring volatile organic compounds for purposes of determining compliance
with emission limits. Where such a method also measures compounds with
negligible photochemical reactivity, these negligibly-photochemical reactive
compounds may be excluded as volatile organic compounds if the amount of such
the compounds is
accurately quantified and such the exclusion is approved by the department.